Arwen-Undomiel.com
http://arwen-undomiel.com/forum/

Ammy's Semi-Regular Tutorial Thread
http://arwen-undomiel.com/forum/viewtopic.php?f=37&t=20692
Page 1 of 1

Author:  Ammy Dawne [ January 20th, 2010, 3:22 pm ]
Post subject:  Ammy's Semi-Regular Tutorial Thread

Lothy will probably be the only one using these, but I figured it might do me some good to practice writing tutorials. Thus, a tutorial thread. =D

I'll be posting as often as I make these, which will sometimes be very often and sometimes not so much. If you have a specific graphic that you'd like a tutorial for, please let me know! It will take priority over the random ones I do. Sorry guys, only Photoshop tutorials for right now. I have Photoshop CS2, but nearly everything I do can be substituted in an earlier version.

Here we go.


[font=georgia]Banner Tutorial - Lighten Effect[/font]

Today we'll be making this:
Image

YOU NEED TO KNOW ABOUT:
--Curves
--Hue/Saturation
--Brightness/Contrast
--ColorFill layers
--Lighten/darken effects


To start off, we need a couple(2) decent quality pictures with relatively dark backgrounds. It can have a light background, too, but darker is better.

I’ll be using:
http://sweetandtalented.com/images/moore/moore59.jpg
-and-
http://sweetandtalented.com/images/moore/moore58.jpg

Now, these pictures are very similar, so we’ll have to make one of them smaller than the other to add some contrast.

STEP 1:
Blend your pictures onto your canvas. 500x200 is my favorite to work with, but I guess it doesn’t matter how big or small it is. (Tip: Use a vector mask instead of just straight-up erasing when you blend, it makes going back and undoing something much easier)

Image

The coloring on the pictures is a little bit off, so there are two ways you can fix this.

STEP1.1(optional):
Curves -
Open up a new curves layer.
RBG: point 1 - 73, 119
Green: point 1 - 137, 121

Image

This really depends on your pictures. The key is to mess with it until it works.


STEP1.2(optional):
This is for if you don’t like curves. It’s a little bit trickier, but it works about the same.

Duplicate the layer you’ll be adjusting.
Go to Image>Adjustments>Variations
Move the lever all the way over to ‘fine’. (Click the image labeled ‘original’ in case you’ve used variations previously.)
More Red: 2 Clicks
More Magenta: 1 Click
More Blue: 2 Clicks
Lighter: 5-6 Clicks

Image

Again, this varies between pictures. Pay attention to the colors that you want less of and click the colors opposite them to even it out.


Now that our pictures are a bit more similar, we move onto the next steps.

STEP 2:
Clean it up. Don’t merge the layers yet, sharpen both layers by going to Filter>Sharpen>Sharpen.
Smooth the skin out with the blur tool, use a small round brush with soft edges at 45% transparency.(Tip: Do not blur over the nostrils, eyebrows, eyes, lips, or hair.)
Take your sharpen tool, set it to 50% transparency and move it over the eyes and lips once.

Image


STEP 3:
Now comes the fun part.
Make a new Curves layer.
RGB: Point 1 - 97,58
Point 2 - 171,165
Blue: Point 1 - 88,74
Point 2 - 141,152

Image


STEP 5:
Duplicate both of your original pictures(with all the touch-ups), move them to the sides a little bit.
Desaturate them (ctrl+shift+U), move the layers to the top of the stack so they’re not effected by your curves layers. Set both layers to Lighten.
Erase the parts that overlap or look funky. (REMEMBER: Use vector masks for erasing!)

Image


STEP 6(optional):
Repeat Step 5 with the smaller picture again, move the new layer to a different spot on the canvas.

Image


STEP 7:
Create a Hue/Saturation layer.
Saturation: +7

Image


STEP 8:
Create a Brightness/Contrast layer.
Brightness: -51
Contrast: +18

Image


STEP 9:
Create a Color Fill layer with #012841 or dark turquoise, set it to Lighten.

Image


STEP 10:
Adding text & Extras.
Go back before Step 8, make a new layer. I had a starry brush for this one, but anything with a nice texture will be fine. Make sure that the brush is white(#FFFFFF) and go over your canvas a few times, mostly around where you’ll be putting your text.

For the dotted brush, I set the layer to 40% opacity and went into the blending options, added a drop shadow with 90% opacity, 1px distance, and 0px size.

Image

The fonts I used are 0514oem at 8pt (80% height, 300px spacing) and Bickham Script Pro at 36pt. I set both of the blending options to drop shadow 100% opacity, 1px distance, and 0px size.

Image


And we’re finished!

---------------------------

Author:  Nurrantiel Mashiara [ January 21st, 2010, 1:20 am ]
Post subject: 

Oh, helpfulness! I don't usually think of vector masks for erasing, so that's a good one. And I usually just merge and go too, so this is good for me.

Author:  Ammy Dawne [ January 21st, 2010, 2:27 am ]
Post subject: 

Glad it helped! if anyone uses the tutorials, I'd love to see what you've made. =)

Page 1 of 1 All times are UTC - 5 hours [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/